JAGUAR

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S501-24 Date: 040501 Body - Window Regulator and Motor S-TYPE S501-24 DATE05104 MODEL 2000 MY-ON S-TYPE VIN L00001-ON Window Regulator and Motor - Available Separately - Repair Procedure Issue: The window regulator and regulator motor for 2000 MY-ON S-TYPE vehicles are now serviceable as separate parts. Action: To install a new front or rear window regulator or new front or rear window regulator motor, follow the relevant workshop procedure for vehicles within the specified VIN range outlined below. Note: The manufacturer of the window regulator and window regulator motor recommends that the self-tapping component be used only twice. Therefore when replacing the window regulator on vehicles from VIN L00600 to M45254, a paint mark must be applied to the motor, and when replacing the window regulator motor on vehicles from VIN M45255 onwards a paint mark must be applied to the regulator. When installing a new window regulator or w

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S501-29 Date: 050801 Instruments - Incorrect Compass Readings S501-29 S-TYPE DATE: 08/05 MODEL 2000 MY-ON S-TYPE VIN: L00001-ON Interior Mirror Compass - Compass Reading Incorrectly - Reroute Wiring Issue: Some S-TYPE vehicles equipped with the interior mirror compass may exhibit a condition where the compass is functioning but reading incorrectly. Cause: Interference from nearby wiring. 2000 Jaguar S-Type (X200) V6-3.0L Page 113 Action: In case of a customer complaint of incorrect compass indication, reroute the interior mirror wiring as outlined below. 1. Remove the auto-dimming interior mirror (see Global Technical Reference GTR Workshop Manual, section 501-09). Note: No wires should cross over the compass circuit board. Each set of wires should be routed as a twisted pair for maximum effect. 2. Reroute the wires around the edge of the plastic casing. 3. Install the auto-dimming interior mirror (see Global Technical Referen

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # 1-130 Date: 020301 WDS - JTP 759/13 Software 1-130 DATE: 03/02 All MODEL All VIN JTP 759/13WDS Software ISSUE: This release note introduces the changes on JTP 759/13. This release is based on JTP 759/12. All of the reflash software on WDS is only available from one area. From the vehicle configuration tab select "Reprogram existing modules" and then select the module to be programmed. VEHICLE COVERAGE JTP 759/13 software covers the following NAS vehicle ranges shown. ACTION: To install the software, turn on the WDS. At the VIN prompt, insert the JTP 759/13 CD in the drive. The software will begin to load automatically which will take approximately 15 minutes. In addition, note that at the end of the software installation, the WDS will now perform a scandisk procedure. Note: Unlike the PDU, the WDS software CD does not need to remain in the CD drive after it has been installed. All data resides on the hard drive in

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S307-06 Date: 020501 A/T - Difficult Range Selection/No Start Condition S307-06 DATE 05/02 S-TYPE MODEL 2000-02 MY S-TYPE VIN L00001-M45255 Difficulty Selecting Range - Stiff Or Restricted Movement - Revised Selector Lever Cable Issue: Some owners of 2000-02 MY S-TYPE vehicles may experience difficult range selection, or an inability to start the vehicle. These conditions can be caused by the following: ^ The inner transmission selector lever cable movement is restricted/stiff. ^ The outer transmission selector lever cable appears to be moving within the crimped ends. An improved selector lever cable entered production on later vehicles to solve this condition. Action: In case of a customer complaint of the above conditions on a 2000-2002 MY S-TYPE vehicle, install the new improved selector lever cable, available under the existing part number (XRB 33366).

$80.85 End Date: Saturday Nov-30-2019 10:06:19 PST Buy It Now for only: $80.85 Buy It Now | Add to watch list

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S204-05 Date: 000301 Suspension - Rear Tie Rod Modification Procedure S204-05 S-TYPE DATE 03/00 MODEL 2000 MY-ON S-TYPE VIN L00001-L06640 Rear Suspension Toe Links (Tie Rod Assemblies) - Larger Mounting Stud - Modification Procedure Issue: Beginning with VIN L06641,the inner mounting of the rear suspension toe links (tie rod assemblies) changed from 10 mm to 12 mm mounting stud diameter. Toe links of early design are no longer available. If a replacement toe link is required, it is necessary to modify the rear cross member to accept the later design of toe link. This modification must be performed on both sides of the vehicle and both toe links replaced with the later design, 2000 Jaguar S-Type (X200) V6-3.0L Page 40 even if the original need was only to replace one toe link. Action: If it is necessary to replace a rear toe link on a 2000 MY S-TYPE vehicle within the above VIN range, open out the inner mounting point in the re

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S100-03 Date: 990801 Engine Oil - Viscosity Chart S100-03 DATE 8/99 MODEL 2000 MY-ON S-TYPE VIN L00001-ON Engine Oil - Viscosity/Temperature Chart Issue: Jaguar has found that the use of an engine oil with a viscosity higher than that desirable in certain operating conditions can affect the operation of the Variable Valve Timing, (VVT) unit used on the 3.0 Liter V6 engine. As a result, it has been decided to adopt a common engine oil standard across all V6 and V8 engines. Oils must not be used in temperatures outside the limits indicated for each viscosity grade in the chart below. The information contained in this Technical Bulletin also supersedes that contained in the Driver's Handbook. Any damage resulting from the use of engine oils other than those viscosities specified by Jaguar Cars will not be covered by Jaguar Warranty, and will therefore be the sole responsibility of the dealer or customer concerned. Action: Follo

C $462.74 End Date: Saturday Nov-30-2019 1:00:52 EST Buy It Now for only: C $462.74 Buy It Now | Add to watch list

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S501-02 Date: 990901 Side Impact Sensors - Revised Mounting Torque S501-02 DATE 9/99 MODEL 2000 MY-ON S-TYPE VIN L00001-ON Side Impact Sensors - Revised Mounting Torque - Not In JTIS Issue: The torque specification is revised for the 6 mm. flanged screws that retain the two side impact sensors to the cross member. Action: Use the torque value of 12 Nm +/- 1 instead of 8 Nm +/-1, given in early issues of JTIS. The JTIS procedure for removal and installation may be followed in all other details. (SRO 76.73.53). Warranty Information: This Technical Bulletin is issued for information only.

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # 6-73 Date: 990701 JTIS - CD ROM Shop Manual Issue 7 6-73 DATE 7/99 All MODEL All VIN 2000 Jaguar S-Type (X200) V6-3.0L Page 11 Jaguar Technical Information System (JTIS) - Issue 7 - Workshop Manual - CD-ROM ISSUE: Workshop manual information for 2000 MY S-TYPE, 1995-99 MY Sedan Range and 1997-99 XK8 has been released on CD-ROM (Part No. JJM 10 30 99/95) for use with the multimedia training PC. ACTION: Ensure that the software is installed from the lower CD-ROM drive (E: drive). Refer to the inside cover of the CD-ROM jewel case for installation instructions. Once this CD-ROM has been installed, the system will not accept the JTIS Issue 6 CD-ROM. Note: Store this CD-ROM in a secure place. Do not lose or misplace the JTIS CD-ROM as it will not be replaced free of charge unless it is defective. The price reflects the fact that JTIS Issue 7 is no longer a pilot CD. Additional CD-ROMs must be ordered through the zone parts departme

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S310-01 Date: 011001 Campaign - Poor Engine Performance/Low Fuel Pressure S310-01 S-TYPE DATE 12/99 Amended 10/01 MODEL 2000 MY S-TYPE VIN L00600-L27499 Loss of Engine Performance - Low Fuel Pressure - Replace Fuel Delivery Module Hose - Service Action S144 Remove and destroy Bulletin S310-01, dated 12/99. Replace with this Bulletin. This repair is now a Service Action. Issue: On some 2000 MY S-TYPE vehicles within the above VIN range, additives in certain fuel blends may lead to premature failure of a hose that is part of the fuel delivery module (the main pump assembly) located in the right side of the fuel tank. The hose concerned connects the pump outlet to an in-line filter. Hose failure may lead to abnormally low pressure in the fuel system, with a resulting loss of engine performance. A hose manufactured from a different material entered production from VIN L27500. Action: On all 2000 MY S-TYPE vehicles within the above V

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S419-01 Date: 000801 Navigation System - Diagnostic Menu and Troubleshooting S419-01 S-TYPE DATE 08/00 MODEL 2000 MY-ON S-TYPE VIN L00001-ON Navigation System Diagnosis - Access to Diagnostic Menu - Troubleshooting Issue: This Technical Bulletin provides diagnostic information for the Navigation System used on S-TYPE vehicles. Within the Navigation System there is a Diagnostic Procedure to which a technician may gain access. The Bulletin contains the following information: Access to the Diagnostic Menu Diagnosis Codes Troubleshooting Flowcharts "Adjust Position" Procedure The Adjust Position Procedure provides a method of rapid re-orientation of the system should a vehicle have been unable to 'see' satellites for some time, during which the vehicle has been transported a considerable distance - a situation which may arise during the delivery cycle, or where a customer's vehicle is on board a car ferry for a

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S501-07 Date: 010301 Interior - Ash Tray Latch Malfunction S501-07 S-Type DATE 03/01 MODEL 2000-01 MY S-TYPE VIN L00001-L86902 Ashtray Latch Malfunction - Revised Latch - Replacement Procedure Issue: Some 2000-01 MY S-TYPE vehicles within the above VIN range may experience customer complaints of the ashtray not functioning correctly. A revised ashtray latch has been introduced into production from VIN L86902. This latch can be installed on cars prior to this VIN that experience this customer complaint. Action: On a customer complaint basis only, the following Workshop Procedure should be followed to rectify the above concern: WORKSHOP PROCEDURE 1. Disconnect the vehicle battery (See Workshop Manual, JTIS CD ROM, section 414-01, SRO 86.15.01). 2. Remove the console for access. (See Workshop Manual, JTIS CD ROM section 501-12, SRO 76.25.01). 3. Turn the console assembly over, to expose the ashtray mounting. Caution: Ensure the con

Warranty Information:Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S303-12 Date: 021201 Engine - No Start or Misfire, Water in Spark Plug Wells S303-12 S-TYPE DATE 12/02 MODEL 2000 MY S-TYPE VIN L00001-L63500 Misfire/Non-Start - Water Ingress Into Spark Plug Wells - Revised On-Plug Coil Cover Issue: This Technical Bulletin has been issued due to a number of V8 4.0L vehicles suffering from water entering the spark plug wells, which could cause a misfire/non-start situation. A revised stiffer on-plug coil cover was introduced to prevent water ingress. Action: In case of a customer complaint of the above condition on a 2000 MY S-TYPE, within the above VIN range, replace the on-plug coil cover if the complaints are found to be caused by water ingress. 1. Open hood and fit fender protectors. 2. Open luggage compartment and displace carpet. 3. Record the following customer settings before disconnecting the battery so they can be reset to the customer's preferred setting: ^ Cl

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # 6-70 Date: 990401 Global VIN - Advanced Notice 6-70 DATE 4/99 All MODEL All VIN Advance Notice Of Global Vehicle Identification Number - 2000 MY ISSUE: The Jaguar S-TYPE, to be introduced early in 1999 as a 2000 MY vehicle, will use a new format of Vehicle Identification Number - the "global" VIN. Current XK8 and V8 XJ Series Models will adopt the global format from the start of 2000 MY production in the summer of 1999. While the global VIN system retains a total of 17 characters, as used on current Jaguar models, there is a change to the sequence in which alpha and numeric characters can occur. The VIN coding for the Jaguar S-TYPE will be typically in the format: SAJDA01GXYFL12345 It is anticipated that S-TYPE VINs will run from LOOOO1 - L99999, then M00001 - M99999, etc. From the start of 2000 MY production, the VIN serial number for XK8 Models will start with A00001 and run to A99999, then B00001 etc. For V8 XJ Seri

C $66.00 End Date: Wednesday Nov-27-2019 12:49:05 EST Buy It Now for only: C $66.00 Buy It Now | Add to watch list

Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.car insurance, auto insurance, auto, car, vehicle, insurance, quote, quotes, online, insurance，auto, autos, car, cars, vehicle, vehicles, used car, pre-owned car, pre-owned vehicle, used auto, used vehicle, rental，auto racing news, car racing news

Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.car insurance, auto insurance, auto, car, vehicle, insurance, quote, quotes, online, insurance，auto, autos, car, cars, vehicle, vehicles, used car, pre-owned car, pre-owned vehicle, used auto, used vehicle, rental，auto racing news, car racing news

Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.car insurance, auto insurance, auto, car, vehicle, insurance, quote, quotes, online, insurance，auto, autos, car, cars, vehicle, vehicles, used car, pre-owned car, pre-owned vehicle, used auto, used vehicle, rental，auto racing news, car racing news

Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.car insurance, auto insurance, auto, car, vehicle, insurance, quote, quotes, online, insurance，auto, autos, car, cars, vehicle, vehicles, used car, pre-owned car, pre-owned vehicle, used auto, used vehicle, rental，auto racing news, car racing news

Safety Administration's Auto Safety Hotline at 1-888-DASH-2-DOT (1-888-327-4236).Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S204-R136 Date: 001201 Recall - Front Lower Ball Joint Inspection/Replacement S204-R136 S-TYPE DATE 11/00 Amended 12/00 MODEL 2000-01 MY S-TYPE 2000 Jaguar S-Type (X200) V6-3.0L Page 44 VIN L00001-L92349 Recall R136 - Front Lower Ball Joints - Check Torque or Replace Remove and destroy Bulletin S204-R136, dated 11/00. Replace with this Bulletin. Revisions are shown with asterisks and black bars. Issue: As a result of ongoing process assessments, Jaguar has identified a safety-related defect on a number of S-TYPE vehicles. On the vehicles involved, it is possible that an under-torque condition may exist on the front lower ball joint assembly This may result in a high bending fatigue loading condition on the joint. In some cases the high bending loads could result in a fracture in the first thread of the ball stud that could then lead to separat

DisclaimerJaguar S-Type (X200) V6-3.0L Technical Service Bulletin # JAGA501-001 Date: 060622 Body - Windshield Damage Diagnostic Guide NUMBER: JAGA501-001 MODEL: ALL DATE: June 22, 2006 SECTION: 501-11 Windshield Damage Diagnostic Aid AFFECTED VEHICLE RANGE: All Jaguar Vehicles CONDITION SUMMARY: INTERPRETATION OF GLASS DAMAGE SYMPTOMS Situation: This information only bulletin has been issued to aid dealers to determine whether windshield damage has been caused by an outside influence, or a manufacturing concern. Action: Follow the steps outlined in the Repair Procedure to determine whether windshield damage has been the result of outside damage. PARTS: Information only WARRANTY: NOTE: The following offer illustrations of common windshield damage conditions and how to determine if the damage is a result of outside influences (not warrantable) or of manufacturing problems (warrantable) Normal warranty policy and procedures apply. Service Information Diagnosis 1. Clean damaged windshield

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S501-09 Date: 010501 Body - Water Leaks Diagnosis S501-09 S-TYPE DATE 05/01 MODEL 2000 MY-ON S-TYPE VIN L00001-ON Water Leaks - Diagnostics Issue: In the event of customers complaining of water leaks on their vehicle, this Technical Bulletin has been issued to give Water Leak Diagnostic information and should be used as a guide only. Action: Before any action can be taken in diagnosing a water leak, it is necessary to question the customer to gain as much information as possible. The following questions should be put to the customer before the diagnostic procedure can be started: ^ When was the first water leak discovered? ^ Was the vehicle damaged in an accident in the leaking area? ^ Does the vehicle leak in the rain or on a wet road? ^ Is the vehicle laden/unladen when it leaks? ^ Does the road surface affect the water leak? ^ Does the vehicle leak in a car wash? ^ Does the vehicle leak when parked on a slope or level ground

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S600-S474 Date: 010901 Emissions System - Engine Breather Scheduled Cleaning S600-S474 S-TYPE DATE 12/00 Amended 09/01 MODEL 2000 - *01* MY S-TYPE VIN L00001 - *L93444* Part-Load Engine Breather - Partial Blockage of Restrictor - Scheduled Cleaning - Service Action S474 Remove and destroy Bulletin S600-S474, dated 12/00. Replace with this Bulletin. Revisions are shown with black bars and asterisks. Issue: Jaguar vehicles with the V8 engine, can experience partial blockage of the restricter in the engine part-load breather during normal service. This blockage would restrict the correct operation of the engine breather system. Until further notice, Jaguar Cars is introducing a routine cleaning procedure for this restricter. Initially this procedure should be performed at the first service opportunity on any S-TYPE vehicle, that has already covered more than 10,000 miles (16,000 Km). This cleaning procedure will then be performed a

C $36.34 End Date: Tuesday Nov-26-2019 10:29:01 EST Buy It Now for only: C $36.34 Buy It Now | Add to watch list

C $36.34 End Date: Tuesday Nov-26-2019 10:29:01 EST Buy It Now for only: C $36.34 Buy It Now | Add to watch list

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S204-09 Date: 030401 Tires/Wheels - Vibration/Shimmy S204-09 S-TYPE DATE 04/02 Amended 04/03 MODEL 2000 MY-ON S-TYPE VIN L00001-ON Vibration/Shimmy - Tire Radial Force Variation - Optimizing Wheels And Tires Remove and destroy Bulletin S204-09, dated 4/02. Replace with this Bulletin. Revisions are shown with asterisks and black bars. Issue: This technical bulletin can assist with resolving customer complaints of vibration/shimmy. Vibration/shimmy can be caused by Radial Force Variation (RFV) in the wheel/tire assemblies and the position of the affected wheels on the vehicle. Action: Note: Access to a Hunter 9700/9712 wheel-balancing machine is required to perform the steps in this technical bulletin. In case of a customer complaint of vibration/shimmy on vehicles, follow the optimization procedures below using a Hunter 9700/9712 balancing machine. TYPES OF OPTIMIZATION PROCEDURES Tire to Wheel Match Mounting Tire is positioned o

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # JAGA100-001 Date: 060925 Interior - Approved Cleaning Products NUMBER JAGA100-001 DATE 25 Sep 2OO6 MODEL ALL SECTION: 100-00 Approved Cleaning Products by Autoglym AFFECTED VEHICLE RANGE: All Jaguar CONDITION SUMMARY: AUTOGLYM CLEANING PRODUCTS APPROVED FOR ALL JAGUAR VEHICLES NOTE: Some Autoglym leather cleaning products that have been introduced over the years that have not gained approval to be used on Jaguar products, may result in a claims dispute and warranty rejection. Only products tested and approved for use on Jaguar vehicles should be used. Situation: This information only bulletin is to notify Dealers of a range of Autoglym?leather cleaning products that have been tested and approved for use on all Jaguar vehicles. PARTS: NOTE: Only products tested and approved for use on Jaguar vehicles should be used. In addition to the Autoglym products listed below, the current Jaguar leather cleaner (C2A1061) may be used. Autogl

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S303-02 Date: 020301 Knock Sensor - Designation Clarification S303-02 DATE 03/02 S-Type MODEL 2000-02 MY S-Type (3.0L) V6 2000 Jaguar S-Type (X200) V6-3.0L Page 94 VIN 3.0L V6 Knock Sensor Designations - Not Based On Cylinder Bank Designations - Clarification Issue: It is important to note that the V6 knock sensors are numbered as front and rear - not based on the engine banks. The front knock sensor (1) is located in the vee at the top of the engine where it senses knocking from bank 2, the left bank (Illustration 1). The rear knock sensor (2) is located on the right side of the block, above the starter motor (Illustration 2), where it senses knocking from bank 1, the right bank, where cylinder 1 is located (Illustration 3). This apparent contradiction must be kept in mind, when using the electrical guides or the DTC summaries. 2000 Jaguar S-Type (X200) V6-3.0L Page 95 ^ DTC P0325 applies to the front knock sensor on top of

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S303-S139 Date: 001201 Campaign - ECM Reflash S303-S139 S-TYPE DATE 12/00 MODEL 2000-01 MY S-TYPE VIN L00001-M02205 S-TYPE ECM Reflash - Service Action S139 Issue: A significant change has been introduced in production to the programming of the Powertrain Control Module (PCM) that provides a perceptible enhancement to the response of the engine, transmission, throttle and to the selected mode of transmission operation. In production, this change has been introduced from VIN M02206. For owners of earlier S-TYPE vehicles to enjoy the same enhanced drivability, we have introduced an Enhancement Program that will enable the new software to be installed into the memory of the PCM. This action is performed using the Worldwide Diagnostic System (WDS) in association with a new JTP 759/3A CD-ROM titled "DISC ISSUE 3A JTP 759." 2000 Jaguar S-Type (X200) V6-3.0L Page 99 This minor re-work should be performed prior to handover (