Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S307-19 Date: 050601
A/T - Harsh or Erratic Shifting
S307-19
S-TYPE
DATE
06/05
MODEL
2000-02 MY
S-TYPE
VIN L00001-M44997
5-Speed Transmission - Erratic or Harsh Shifts - Valve Body Kit Available - Repair Procedure
Issue:
Some 2000-02 MY S-TYPE vehicles within the above VIN range may exhibit erratic or harsh transmission shifts. This can be caused by valve body
or control solenoid failure.
Parts Information:
Warranty Information:
Warranty claims should be submitted quoting the information found in the table.
This will result in payment of the stated time and, where applicable parts/miscellaneous expense codes as listed.
Disclaimer
Action
Note:
Check for connector/wiring and Powertrain Control Module (PCM) faults, ensure the transmission fluid is clean and there is no debris in the
sump. Refer to Global Technical Reference GTR Workshop Manual, section: 307-01 - Diagnosis and Testing. Any faults other than the valve
body kit replacement, are to be carried out as a separate Warranty Claim.
When a fault has been confirmed with the valve body or control solenoid, a new valve body kit must be installed. Follow the Service Instruction
outlined below.
2000 Jaguar S-Type (X200) V6-3.0L Page 273
1. Open driver door.
2. Switch ignition "ON".
3. Apply footbrake, move selector lever to the neutral position and release the footbrake.
4. Switch ignition "OFF".
5. Close driver door.
6. Disconnect battery (see Global Technical Reference GTR Workshop Manual, section: 414-01).
7. Raise vehicle on lift and place a suitable drain pan under the transmission.
8. Undo and remove the transmission drain plug and discard the seal.
9. Allow the transmission fluid to drain.
Note:
Ensure the transmission fluid is clean and there is no debris. If this is not the case, stop and do not perform this bulletin procedure.
10. Install a new fibre washer and install and tighten the drain plug.
11. Align transmission jack under transmission.
12. Place suitable supporting blocks onto the transmission jack and raise to support the transmission.
13. Remove the transmission rear mounting securing bolts.
Caution:
Do not allow the engine to contact the bulkhead.
14. Lower the transmission jack.
Working with an assistant:
15. Raise rear of the transmission by hand and reposition the jack to support the transmission between the sump and rear of transmission main
casing (Illustration 1).
Working alone:
16. Disconnect the Transmission Range (TR) sensor electrical connector.
2000 Jaguar S-Type (X200) V6-3.0L Page 274
17. Remove the TR sensor securing screws, and displace and remove the TR sensor from the transmission (Illustration 2).
Caution:
Ensure the transmission fluid is clean and there is no debris in the sump.
18. Remove transmission fluid pan, gasket and filter (see Global Technical Reference GTR Workshop Manual, section: 307-01).
19. Disconnect the solenoid block electrical connector (Illustration 3).
20. Disconnect the pressure switch electrical connector (Illustration 4).
21. Remove the pressure switch securing bolts. Remove the pressure switch.
2000 Jaguar S-Type (X200) V6-3.0L Page 275
22. Remove the solenoid block securing bolts and remove solenoid block. Remove and discard the 0-rings (Illustration 5).
23. Remove the main control valve body (see Global Technical Reference GTR Workshop Manual, section: 307-01 - 44.40.01 - Removal - Carry
out steps 12 to 17).
24. Install the new main control valve body (see Global Technical Reference GTR Workshop Manual, section: 307-01 - 44.40.01 - Installation -
Carry out steps 1 to 11).
25. Remove the exhaust system (see Global Technical Reference GTR Workshop Manual, section: 309-00).
26. Remove the heat shield securing bolts, and remove the driveshaft heat shield (Illustration 6).
Caution:
Make sure the front of the driveshaft does not put an excessive load on the centre bearing. Failure to follow this instruction may result in
damage to the vehicle.
Note:
Mark the position of the driveshaft in relation to the transmission flange. Mark the position of each nut and bolt in relation to the
transmission flexible joint.
27. Remove the driveshaft securing bolts, detach the driveshaft from the transmission flange.
2000 Jaguar S-Type (X200) V6-3.0L Page 276
28. Using a suitable securing strap, reposition and support the driveshaft to the vehicle body (Illustration 7).
29. Install new transmission fluid filter and gasket, and install the fluid pan (see Global Technical Reference GTR Workshop Manual, section:
307-01).
30. Ensure the manual control lever is in the neutral position.
31. Install the new TR sensor to the manual control lever, install but do not fully tighten the TR sensor securing screws.
32. Align marks on the TR sensor (Illustration 8).
33. Final tighten the TR sensor securing screws to 10 Nm.
34. Connect the TR sensor electrical connector.
2000 Jaguar S-Type (X200) V6-3.0L Page 277
35. Disconnect the Intermediate Shaft Speed (ISS) sensor electrical connector (Illustration 9).
36. Remove the ISS sensor securing screw, and remove the ISS sensor.
37. Install the new ISS sensor; install and tighten the securing screw to 10 Nm.
38. Disconnect the Output Shaft Speed (OSS) sensor electrical connector (Illustration 10).
39. Remove the OSS sensor securing screw, and remove the OSS sensor.
40. Install the new OSS sensor; install and tighten the securing screw to 10 Nm.
2000 Jaguar S-Type (X200) V6-3.0L Page 278
41. Disconnect the Turbine Shaft Speed (ISS) sensor electrical connector (Illustration 11).
42. Remove the ISS sensor securing screw, and remove the 155 sensor.
43. Install the new ISS sensor; install and tighten the securing screw to 10 Nm.
Working with an assistant:
44. Raise rear of the transmission by hand and reposition the jack under the transmission fluid pan.
Working alone:
45. Raise transmission jack to align the transmission to the correct position.
46. Install and fully tighten rear mounting securing bolts.
47. Lower the transmission jack and return transmission jack to the storage area.
48. Detach the driveshaft from body structure (Illustration 12).
49. Attach the driveshaft to the transmission flange; install and tighten the securing bolts and tighten to 85 Nm.
2000 Jaguar S-Type (X200) V6-3.0L Page 279
50. Install the driveshaft heat shield; install and tighten the securing bolts to 5.5 Nm (Illustration 13).
51. Install the exhaust system (see Global Technical Reference GTR Workshop Manual, section: 309-00).
52. Connect battery (see Global Technical Reference GTR Workshop Manual, section: 414-01).
53. Fill the transmission with oil (see Global Technical Reference GTR Workshop Manual, section: 307-01).
54. Ensure the ignition is switched "OFF", parking brake is ON' and the transmission selector lever is in park.
Note:
Ensure WDS is loaded with software release JTP 759/37 or later, switch on and allow software to load VIN input screen.
55. Connect PTU to vehicle using diagnostic cable.
56. Enter VIN and navigate to configuration main menu.
57. Select and run "re-configure existing PCM" application.
58. After the re-configuration of the PCM is complete, switch "OFF" PTU, disconnect from vehicle and return WDS to original location.
What I appreciated most: It's slick beauty in and out and enjoyable to drive sporty performance. IN Beautiful Condition Inside and out! What comes out of the middle-exit tailpipes might lack the volume and anger of different F-types, however there’s no denying the little engine’s nerve. It’s attainable that prime temperatures at our California take a look at facility might have taken some zip out of Jaguar’s 4-banger, but even so, we’d suggest not staring down Boxsters—or V6 Camrys—at purple lights. While the brake pedal might have felt touchy in road driving, it felt good on the observe, the place you’re maximizing braking on a regular basis anyway. We might crave a guide shifter and clutch pedal for enhancing our interface with the F-Type. Although Jaguar provides a six-speed handbook on V6 F-sorts, the take charge is under two p.c, so it ought to come as no surprise that Jaguar didn’t hassle with a 2.0-liter guide. 2014 Jaguar F-Type V8 S Roadster finished in a head-turning Italian Racing Red over a fabulous interior tailor-made in the finest Jet Black hides, with Black Soft Top.