Jaguar XF (X250) V85.0L SC # JTB00280
Date: 121212
Lighting Erratic Front Overhead Console Lamp Operation
JTB00280NAS1
12DEC12
SECTION: 50112
Front Overhead Console Lamps do not Operate as Expected
AFFECTED VEHICLE RANGE:
XF (X250)
VIN: R00019S34279
Model Year: 20092012
CONDITION SUMMARY:
Situation:
The front overhead console lamps may not operate as expected.
Cause:
This may be caused by issues within the printed circuit board (PCB) in the lamp assembly.
Action:
In the event of a customer concern of the above, refer to the Repair Procedure outlined below.
PARTS
TOOLS:
Refer to Workshop Manual / Repair Procedure for any required special tools
WARRANTY
REPAIR PROCEDURE
1. Refer to Workshop Manual section 50112 (steps 1 and 2 only) and remove the front overhead console lamp assembly.
2. WARNING: The pink bubble wrap that is used for packaging may be used as a work mat.
NOTE:
Make sure no damage is caused when removing the electrical connectors.
3.
4.
5.
Page 140
Disconnect the two electrical connectors.
NOTE: Some items removed for clarity.
Move aside the black plastic cover.
NOTE: Make sure no damage is caused when unclipping the small printed circuit boards.
Using a suitable tool, unclip the three small printed circuit boards.
NOTE: Make sure no damage is caused when unclipping the electrical connector.
Using a suitable tool unclip the electrical connector.
6.
7.
8.
^
Page 141
Release the two securing clips.
NOTE: Make sure no damage is caused when removing the printed circuit board.
Remove the main circuit board.
NOTE: Make sure all the grease is removed from the electrical connectors.
Using a suitable clean cloth remove the grease on the three electrical connectors.
^
Using the wipe supplied in the kit make sure all the grease is removed from the electrical connectors.
CAUTION: When installing the rubber sleeves it is important not to damage or split them.
9.
10.
11.
Page 142
NOTE:
Install all three sleeves from the top.
Install the three rubber sleeves to the electrical connectors.
^
The rubber sleeves must be approximately 23 mm from the bottom of the electrical connector.
CAUTION: Prior to touching the new printed circuit boards it is advised that your hands are clean and you have earthed your body
out by touching the steel work bench.
Change over the three interior light bulbs from the old printed circuit board to the new printed circuit board.
NOTE: Make sure no damage is caused when installing the ne printed circuit board.
NOTE:
Locate the printed circuit boards into the four locating fixings before clipping the printed circuit board into position.
Install the new printed circuit board.
NOTE: Make sure no damage is caused when installing the three small printed circuit boards.
12.
Page 143
Install the three small printed circuit boards.
NOTE: Make sure the electrical ribbon is square in the connector, before it is fully engaged.
NOTE:
Make sure no damage is caused when installing the electrical connectors.
Connect the electrical connector.
^
Push in the two securing clips.
13. Install the black plastic cover.
14. NOTE: Make sure no damage is caused when installing the electrical connectors.
Page 144
Connect the two electrical connectors.
15. Refer to Workshop Manual section 50112 (steps 2 and 1 only) and install the front overhead console lamp assembly.
16. Verify front overhead console lamp operation.
Date: 121212
Lighting Erratic Front Overhead Console Lamp Operation
JTB00280NAS1
12DEC12
SECTION: 50112
Front Overhead Console Lamps do not Operate as Expected
AFFECTED VEHICLE RANGE:
XF (X250)
VIN: R00019S34279
Model Year: 20092012
CONDITION SUMMARY:
Situation:
The front overhead console lamps may not operate as expected.
Cause:
This may be caused by issues within the printed circuit board (PCB) in the lamp assembly.
Action:
In the event of a customer concern of the above, refer to the Repair Procedure outlined below.
PARTS
TOOLS:
Refer to Workshop Manual / Repair Procedure for any required special tools
WARRANTY
REPAIR PROCEDURE
1. Refer to Workshop Manual section 50112 (steps 1 and 2 only) and remove the front overhead console lamp assembly.
2. WARNING: The pink bubble wrap that is used for packaging may be used as a work mat.
NOTE:
Make sure no damage is caused when removing the electrical connectors.
3.
4.
5.
Page 140
Disconnect the two electrical connectors.
NOTE: Some items removed for clarity.
Move aside the black plastic cover.
NOTE: Make sure no damage is caused when unclipping the small printed circuit boards.
Using a suitable tool, unclip the three small printed circuit boards.
NOTE: Make sure no damage is caused when unclipping the electrical connector.
Using a suitable tool unclip the electrical connector.
6.
7.
8.
^
Page 141
Release the two securing clips.
NOTE: Make sure no damage is caused when removing the printed circuit board.
Remove the main circuit board.
NOTE: Make sure all the grease is removed from the electrical connectors.
Using a suitable clean cloth remove the grease on the three electrical connectors.
^
Using the wipe supplied in the kit make sure all the grease is removed from the electrical connectors.
CAUTION: When installing the rubber sleeves it is important not to damage or split them.
9.
10.
11.
Page 142
NOTE:
Install all three sleeves from the top.
Install the three rubber sleeves to the electrical connectors.
^
The rubber sleeves must be approximately 23 mm from the bottom of the electrical connector.
CAUTION: Prior to touching the new printed circuit boards it is advised that your hands are clean and you have earthed your body
out by touching the steel work bench.
Change over the three interior light bulbs from the old printed circuit board to the new printed circuit board.
NOTE: Make sure no damage is caused when installing the ne printed circuit board.
NOTE:
Locate the printed circuit boards into the four locating fixings before clipping the printed circuit board into position.
Install the new printed circuit board.
NOTE: Make sure no damage is caused when installing the three small printed circuit boards.
12.
Page 143
Install the three small printed circuit boards.
NOTE: Make sure the electrical ribbon is square in the connector, before it is fully engaged.
NOTE:
Make sure no damage is caused when installing the electrical connectors.
Connect the electrical connector.
^
Push in the two securing clips.
13. Install the black plastic cover.
14. NOTE: Make sure no damage is caused when installing the electrical connectors.
Page 144
Connect the two electrical connectors.
15. Refer to Workshop Manual section 50112 (steps 2 and 1 only) and install the front overhead console lamp assembly.
16. Verify front overhead console lamp operation.