Skip to main content

Jaguar XF (X250) V8-5.0L SC Technical Service Bulletin # JTB002132 Date: 110728

Jaguar XF (X250) V8-5.0L SC Technical Service Bulletin # JTB002132 Date: 110728



Electrical - Vehicle Battery Is Discharged



No: JTB00213



ISSUE: 2



DATE: 28 JULY 2010



ISSUE "2" CHANGES ARE HIGHLIGHTED IN GRAY



SECTION: 418



Battery Discharged



AFFECTED VEHICLE RANGE:



XF (X250) VIN: R00019 -504549



Model Year: 2009 - 2011



XK (150) VIN: B32753 - B42709



Model Year: 2010 - 2011



CONDITION SUMMARY:



Situation:



The vehicle battery may become discharged, for no apparent reason, after the vehicle is parked overnight or similar period of non-use. This may be



due to a MOST bus issue causing a 1.6Amp drain when the Infotainment Control Module (ICM) is shut down.



NOTE:



This software update should be carried out on any customer complaint of a discharged battery. The cause of the discharged battery must be



investigated as per normal processes; any other faults found must be claimed as a separate claim.



Action:



In the event of a customer concern of the above, refer to the Repair Procedure outlined below to update the ICM software.



PARTS:



No parts necessary



TOOLS:



IDS with latest IDS-DVD and Calibration File; first available on IDS-DVD123_V7.08 Calibration File 56 Jaguar-approved Midtronics Vehicle



Power Supply Refer to Workshop Manual for any required special tools



45



WARRANTY



REPAIR PROCEDURE



UPDATE INFOTAINMENT CONTROL MODULE SOFTWARE



CAUTION:



Ensure all ignition "ON" / ignition "OFF" requests are carried out; failure to perform these steps may cause damage to control modules in the



vehicle.



CAUTION:



A Jaguar-approved Midtronics Vehicle Power Supply must be connected to the vehicle battery during IDS diagnosis / module programming.



1. Connect the Jaguar-approved Midtronics Vehicle Power Supply to the vehicle battery.



2. Turn ignition ON (engine not running).



NOTE:



IDS must be loaded with IDS-DVD123_V7.08 or later and Calibration File 56 or later.



3. Connect the IDS to the vehicle and begin a new Symptom Driven Diagnostics (SDD) session.



4. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle.



5. From the Session Type selection screen, choose "Diagnosis".



6. Select the Selected Symptoms tab, and then select one of the following:



^ Powertrain > Engine system > Starting system > Will not start > Cranks too slow or



^ Powertrain > Engine system > Starting system > Will not start > Will not crank or



^ Electrical > Battery> Quiescent current> Quiescent too high or



^ Electrical > Battery> Charging system> Flat battery or



^ Electrical > Battery> Power distribution > Ignition supplies> No ignition



7. Select "continue".



8. Select the Recommendations tab.



9. From the Recommendations screen, select Run to configure the Infotainment control module



^ Follow all on-screen instructions to complete this task.



10. Exit the current session.



11. Disconnect the IDS and the Midtronics Vehicle Power Supply from the vehicle.

Labels:

Comments

Post a Comment

Popular posts from this blog

Integrated Control Panel (FCDIM)

Integrated Control Panel (FCDIM) Diagnostic Trouble Code (DTC) Index Integrated Control Panel (FCDIM) CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee confirmation of a fault and may also cause additional faults in the vehicle being checked and/or the donor vehicle. CAUTION: When probing connectors to take measurements in the course of the pinpoint tests, use the adaptor kit, part number 3548-1358-00. 2012 Jaguar XJ (X351) V8-5.0L SC   284 NOTE: If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval programme is in operation, prior to the installation of a new module/component. NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed
Post a Comment
Read more

Adaptive Damping Module (SUMB)

Adaptive Damping Module (SUMB) Diagnostic Trouble Code (DTC) Index Adaptive Damping Module (SUMB) CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee confirmation of a fault and may also cause additional faults in the vehicle being checked and/or the donor vehicle. CAUTION: When probing connectors to take measurements in the course of the pinpoint tests, use the adaptor kit, part number 3548-1358-00. NOTE: If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval programme is in operation, prior to the installation of a new module/component. NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra
Post a Comment
Read more