Skip to main content

Jaguar S-Type #J0043 Date: 090305 Recall - ECM/TCM Update For OBD Compliance NUMBER DATE MODEL S-TYPE

Jaguar S-Type #J0043 Date: 090305
Recall - ECM/TCM Update For OBD Compliance
NUMBER
DATE
MODEL
S-TYPE
XJ,
XK
X-TYPE
ISSUE '3' CHANGES ARE HIGHLIGHTED WITH GRAY BACKGROUND
SECTION: 303
EMISSIONS RECALL J004: Revised On-Board Diagnostic System Software
AFFECTED VEHICLE RANGE
CONDITION SUMMARY:
Situation:
A number of emission regulations non-compliance issues relating to the On-Board Diagnostic (OBD) system function covering thermostat
diagnostic, calibration verification, in-use monitor performance ratio, and an emission issue relating to open loop smoothing (vehicle remains in
open loop after fuel cut-off for prolonged periods) have been identified. In addition, a group of deficiencies have been identified within the OBD
system function related to the evaporative leak diagnostic.
NOTE:
Customers should be informed that after the adaption clearing procedure and reconfiguration repair, the transmission shift quality will improve over
time as the transmission adapts to the customer's individual driving requirements.
Action:
Dealers are to update the affected vehicles' Engine Control Module (ECM), and where applicable the Transmission Control Module (TCM),
software as outlined in the Repair Procedure below. Consult the table containing the model years, VIN range, and repairs required prior to
performing any software updates.
Owners will be notified by Customer Letter of this Recall with the request that they contact a dealer to have the update(s) performed. At the time of
customer appointment, ensure that all outstanding service campaigns for each individual vehicle are identified and allocate sufficient time and
resources to complete all campaigns. To identify repaired vehicles, US dealers must complete and install a Service Action 'Authorized Modifications'
label on the radiator support panel. California dealers are required by the California Code of Regulations to complete a salmon-colored 'Vehicle
  Page 304
Emissions Recall - Proof of Correction' certificate. This form must be provided to the customer for vehicles registered in California when the Recall
work has been completed.
PARTS
WARRANTY
REPAIR PROCEDURE

Comments

Popular posts from this blog

Integrated Control Panel (FCDIM)

Integrated Control Panel (FCDIM) Diagnostic Trouble Code (DTC) Index Integrated Control Panel (FCDIM) CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee confirmation of a fault and may also cause additional faults in the vehicle being checked and/or the donor vehicle. CAUTION: When probing connectors to take measurements in the course of the pinpoint tests, use the adaptor kit, part number 3548-1358-00. 2012 Jaguar XJ (X351) V8-5.0L SC   284 NOTE: If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval programme is in operation, prior to the installation of a new module/component. NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed

Adaptive Damping Module (SUMB)

Adaptive Damping Module (SUMB) Diagnostic Trouble Code (DTC) Index Adaptive Damping Module (SUMB) CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee confirmation of a fault and may also cause additional faults in the vehicle being checked and/or the donor vehicle. CAUTION: When probing connectors to take measurements in the course of the pinpoint tests, use the adaptor kit, part number 3548-1358-00. NOTE: If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval programme is in operation, prior to the installation of a new module/component. NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra