Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S303-S139 Date: 001201

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S303-S139 Date: 001201

Campaign - ECM Reflash

S303-S139

S-TYPE

DATE 12/00

MODEL

2000-01 MY

S-TYPE

VIN

L00001-M02205

S-TYPE ECM Reflash - Service Action S139

Issue:

A significant change has been introduced in production to the programming of the Powertrain Control Module (PCM) that provides a perceptible

enhancement to the response of the engine, transmission, throttle and to the selected mode of transmission operation. In production, this change has

been introduced from VIN M02206.

For owners of earlier S-TYPE vehicles to enjoy the same enhanced drivability, we have introduced an Enhancement Program that will enable the

new software to be installed into the memory of the PCM. This action is performed using the Worldwide Diagnostic System (WDS) in association

with a new JTP 759/3A CD-ROM titled "DISC ISSUE 3A JTP 759."

2000 Jaguar S-Type (X200) V6-3.0L Page 99

This minor re-work should be performed prior to handover (in the case of all unsold vehicles) or at the first service opportunity/next Dealer visit (in

the case of all vehicles already in service).

This Service Action supersedes Service Action S129 - no further claims for reprogramming of the PCM under S129 will be accepted. S139

supersedes all previous reflash software.

Action:

Perform this reflash on all S-TYPE vehicles in the VIN range L00001-M02205. This update must be performed on all unsold vehicles before

delivery to the customer. It must be performed at the next service opportunity for vehicles already in service.

^ Do not use the S129 PDU software for any more PCM updates. Remove this software from active use.

Note:

Use this opportunity to check for any other outstanding service actions or recalls that may need to be performed on the vehicle.

REFLASH POWERTRAIN CONTROL MODULE (PCM)

Caution:

Before starting the reprogramming procedure, make sure DISC ISSUE 3A JTP 759 is installed on the WDS. Do not use ISSUE 3.

1. Open hood. Place protective covers over the fenders.

2. Temporarily remove the transit isolation device if it is still present on the vehicle and reconnect the battery

3. Switch 'ON' the WDS. (Press green button).

4. While the WDS is powering-up, connect the diagnostic cable to the WDS and the vehicle.

Note:

Ensure that WDS remains in docked position throughout procedure. Ensure socket is securely connected.

5. If a previous session exists in the memory of WDS, a pop-up message will appear 'AN INCOMPLETE SESSION WAS FOUND, DO YOU

WISH TO CONTINUE THE SESSION?' Select 'NO', then. (Press check mark on display).

6. Wait for pop-up message 'CONFIRM CHOICE', select one item, then (Press check mark on display).

7. Enter VIN (last six digits), then (Press check mark on display).

8. Read warning screen, then (Press check mark on display).

9. Read second warning screen, then (Press check mark on display).

10. Wait for pop-up message 'DO YOU WISH TO READ CONFIGURATION INFORMATION FROM THE VEHICLE?' Select 'NO', then

(Press check mark on display).

11. Wait for pop-up message 'IS THE CONFIGURATION CORRECT?' Select 'YES', then (Press check mark on display). (Based on the VIN, the

display will show 99.25, 00, or 01 as the model year. Early VINs will indicate as 99.25 model year on the WDS.)

12. Wait for pop-up message 'DO YOU WISH TO READ THE DTC'S NOW?' Select 'NO', then (Press check mark on display).

13. Wait for pop-up message 'ADAPTIVE DAMPING?' Select one choice, then (Press check mark on display).

14. Select the 'VEHICLE CONFIGURATION' tab, which has the symbol showing a wrench over a car.

15. Select 'CONFIGURE EXISTING MODULE' from menu, then (Press check mark on display).

16. Select 'POWER TRAIN CONTROL MODULE' from menu, then (Press check mark on display).

2000 Jaguar S-Type (X200) V6-3.0L Page 100

Note:

In some cases, instead of seeing this you will be presented with a list of unknown calibration files.

If this happens, abort the operation. Use the system disc JTP 752 to re-ghost the WDS. Then load DISC ISSUE 3A JTP 759 again and

repeat the procedure from the beginning.

17. Wait for pop-up message 'ENGINE TYPE'. Select choice, then (Press check mark on display).

18. Wait for pop-up message 'TRANSMISSION'. Select choice, then (Press check mark on display).

19. Select Calibration Type from menu entitled CALIBRATION SELECT, appropriate to the vehicle market specification, then (Press check

mark on display).

Note:

When highlighting a Calibration File, all the markets that are affected will be displayed on right-hand side of screen. Ensure the

Calibration File is correct for the vehicle specification.

20. Wait for pop-up message 'WARNING! SELECTING THE WRONG CALIBRATION FILE WILL CAUSE THE EMISSION

SPECIFICATION OF THIS VEHICLE TO BE INCORRECT DO YOU WISH TO CONTINUE?' Select 'YES', then (Press check mark on

display).

21. Wait for pop-up message 'SET IGNITION SWITCH TO IGNITION ON'. Switch ignition 'ON', then (Press check mark on display).

22. Wait for pop-up message 'CALIBRATION FILENAME OK: ********** UPDATE CALIBRATION FILE? Select 'YES', then (Press check

mark on display).

23. Wait for pop-up message 'SWITCH IGNITION OFF'. Switch ignition 'OFF', then (Press check mark on display).

24. Wait for pop-up message 'SWITCH THE IGNITION ON'. Switch the ignition 'ON', then (Press check mark on display).

25. The pop-up message 'PROGRAMMING IN PROCESS' will appear. (This takes approximately six minutes)

26. On both 3.0L V6 and 4.0L V8 vehicles, visually inspect air cleaner for loose, faulty or damaged clips. (Illustration 1)

Note:

2000 Jaguar S-Type (X200) V6-3.0L Page 101

Secure any loose clips. If the clips are faulty or damaged, replace as necessary.

27. If the vehicle is 4.0L VB, visually inspect lower edge of the spark plug coil covers for water seepage. (Illustration 2). If the vehicle is a 3.0L

V6, continue to step 28.

Note:

If watermarks are visible, remove the coil cover to identify if any coils may be corroded. If corrosion is found, replace any damaged coils,

and replace the affected coil cover with part no. AJ8 3078.

28. On all vehicles, wait for pop-up message SWITCH IGNITION TO OFF'. Switch ignition 'OFF', then (Press check mark on display).

29. Wait for pop-up message 'PROGRAMMING COMPLETE', then (Press check mark on display).

30. Disconnect diagnostic cable from the vehicle and the WDS.

31. Shut down the WDS.

32. Reinstall the transit isolation device if the car is unsold.

INSTALL AUTHORIZED MODIFICATION LABEL

Enter your dealer number and the date on the Authorized Modification Label (Illustration 3). Apply the label to the left B-post below the striker.

Then apply the clear sheet over the label. Place the label over any S129 label that might be present. Do not cover an S120 label if present.

To avoid confusion, discard any S120/S129 or S129 only stickers remaining in inventory.

Parts Information

2000 Jaguar S-Type (X200) V6-3.0L Page 102

Warranty Information

NOTE:

Always perform a DCS claim search first to determine whether this service action has been performed on this vehicle. The warranty selection

under the vehicle inquiry will give a listing of all claims against the vehicle. If S139 appears in the fault code field, do not perform this service

action.

CLAIM SUBMISSION PROCEDURE:

Warranty summary codes have been assigned to this service action in order to simplify claim submission. The dealership will be reimbursed the parts

and labor time allowance as indicated.

DCS DEALERS

Submit claims using the appropriate summary code for the vehicle model and work performed. Follow standard campaign submission procedures.

NON-DCS DEALERS

Submit claims on the Recall Campaign Summary form W-25.