Jaguar XF (X250) V85.0L SC # JTB001872
Body Rear Door Window Glass Operating Issues
No. JTB00187
Issue: 2
Date: 20 MAY 2010
ISSUE '2' CHANGES ARE HIGHLIGHTED IN GRAY
SECTION: 501
Rear Door Window Glass Closing Incorrectly
Date: 100520
Page 127
AFFECTED VEHICLE RANGE:
CONDITION SUMMARY:
Situation:
The left and rightrear door window glass may close and then immediately reopen or the one touch up function may be inoperative. This
may be caused by the Hall sensor incrementing when the vehicle 'wakes up', causing the door module to record the incorrect glass
position.
Action:
In the event of a customer concern of the above, refer to the Repair Procedure outlined below to configure the Drivers and Passengers
Door Modules and initialize the windows.
PARTS:
No parts necessary
TOOLS:
IDS with latest IDSDVD and Calibration File; first available on IDSDVD120_V6.02 Calibration File 25 Jaguarapproved Midtronics
Vehicle Power Supply
WARRANTY:
NOTE:
Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as
guidance only. Always refer to DDW to obtain the latest repair time.
DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a quantity of zero.
Normal warranty policy and procedures apply.
REPAIR PROCEDURE
CAUTION:
Ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform these steps may cause damage to control modules
in the vehicle.
CAUTION:
A Jaguarapproved Midtronics Vehicle Power Supply must be connected to the vehicle battery during IDS diagnosis / module
programming.
1. Connect the Jaguarapproved Midtronics Vehicle Power Supply to the vehicle battery.
NOTE:
IDS must be loaded with IDSDVD120_V6.02 or later and Calibration File 25 or later.
2. Connect the Integrated Diagnostic System (IDS) to the vehicle and begin a new Symptom Driven Diagnostics (SDD) session.
3. Follow the onscreen prompts, allowing SDD to read the VIN and identify the vehicle.
4. From the Session Type selection screen, choose 'Diagnosis'.
5. Select the Selected Symptoms tab, and then select:
^
Body > Glass panels > Glass movement
6. Select 'Continue'.
Page 128
7. Select the Recommendations tab.
8. From the Recommendations screen, select Run to configure the 'Drivers door module'.
^
Follow all onscreen instructions to complete this task.
9. From the Recommendations screen, select 'Run' to configure the 'Passenger's door module'.
^
Follow all onscreen instructions to complete this task.
10. Exit the current session.
11. Disconnect the IDS and the Midtronics Vehicle Power Supply from the vehicle.
NOTE:
Global Technical Reference (GTR) lookup sequence is as follows:
GTR Home > NAS > X250XF > Service Information > 2010 > Workshop Manual
12. Refer to Workshop Manual (GTR) section 50111, Glass, Frames and Mechanisms, and perform the door window motor initialization
procedure.
13. Verify one touch up and antitrap functions of all windows.
Disclaimer
Body Rear Door Window Glass Operating Issues
No. JTB00187
Issue: 2
Date: 20 MAY 2010
ISSUE '2' CHANGES ARE HIGHLIGHTED IN GRAY
SECTION: 501
Rear Door Window Glass Closing Incorrectly
Date: 100520
Page 127
AFFECTED VEHICLE RANGE:
CONDITION SUMMARY:
Situation:
The left and rightrear door window glass may close and then immediately reopen or the one touch up function may be inoperative. This
may be caused by the Hall sensor incrementing when the vehicle 'wakes up', causing the door module to record the incorrect glass
position.
Action:
In the event of a customer concern of the above, refer to the Repair Procedure outlined below to configure the Drivers and Passengers
Door Modules and initialize the windows.
PARTS:
No parts necessary
TOOLS:
IDS with latest IDSDVD and Calibration File; first available on IDSDVD120_V6.02 Calibration File 25 Jaguarapproved Midtronics
Vehicle Power Supply
WARRANTY:
NOTE:
Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as
guidance only. Always refer to DDW to obtain the latest repair time.
DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a quantity of zero.
Normal warranty policy and procedures apply.
REPAIR PROCEDURE
CAUTION:
Ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform these steps may cause damage to control modules
in the vehicle.
CAUTION:
A Jaguarapproved Midtronics Vehicle Power Supply must be connected to the vehicle battery during IDS diagnosis / module
programming.
1. Connect the Jaguarapproved Midtronics Vehicle Power Supply to the vehicle battery.
NOTE:
IDS must be loaded with IDSDVD120_V6.02 or later and Calibration File 25 or later.
2. Connect the Integrated Diagnostic System (IDS) to the vehicle and begin a new Symptom Driven Diagnostics (SDD) session.
3. Follow the onscreen prompts, allowing SDD to read the VIN and identify the vehicle.
4. From the Session Type selection screen, choose 'Diagnosis'.
5. Select the Selected Symptoms tab, and then select:
^
Body > Glass panels > Glass movement
6. Select 'Continue'.
Page 128
7. Select the Recommendations tab.
8. From the Recommendations screen, select Run to configure the 'Drivers door module'.
^
Follow all onscreen instructions to complete this task.
9. From the Recommendations screen, select 'Run' to configure the 'Passenger's door module'.
^
Follow all onscreen instructions to complete this task.
10. Exit the current session.
11. Disconnect the IDS and the Midtronics Vehicle Power Supply from the vehicle.
NOTE:
Global Technical Reference (GTR) lookup sequence is as follows:
GTR Home > NAS > X250XF > Service Information > 2010 > Workshop Manual
12. Refer to Workshop Manual (GTR) section 50111, Glass, Frames and Mechanisms, and perform the door window motor initialization
procedure.
13. Verify one touch up and antitrap functions of all windows.
Disclaimer